Herman Miller® Ethospace® Parts

Monorail

This monorail attaches to the top of a frame to mount an adjustable spotlight. D-style vertical storage unit, screen, or toll rail. It is anodized aluminum with cool grey neutral (CL) ends. Part # E1267
Available widths:18",24",30",36",42",48"

Frame Top Cap

This cap trims the top of a frame. It has a painted steel, enameled or veneer surface.
Part #E1260

Connector Top Cap

This cap trims the top of a vinyl or fabric covered radius shaped connector or spacer and replaces a standard connector top cap.
Part #E1261

Power Entry External Direct

Connects a buildings electrical supply from a wall, floor or column to the base of an powered frame. Plugs directly into a receptacle location on the frames baseline to distribute up to 4-20 amp circuits. Right hand direction but can be field converted to a left hand direction.
Part # E1322
Available lengths: 6',12',18',24'

Power Entry Internal Direct

Connects a buildings electrical supply from a wall, floor or column to a powered frame. It enters the frame through the ends of the cable management cover and plugs in to the right hand receptacle outlet to a power harness. The power entry includes a 6' cable that can be field cut to the appropriate length.
Part # E1325

Base Power Entry Junction Box

This power entry connects a buildings electrical supply from a wall, floor, or column to the base of a non-powered frame. and distributes up to 4-20 amp circuits. It includes a junction box,1 plain or grooved cable management side cover, and 6' of wire that can be field cut to the appropriate length for connection to the buildings power. Part # E1323

Frame Power Entry

This 4-circuit power entry connects a buildings electrical supply from a floor monument or wall junction box to an adjacent powered frame. It is concealed as it enters the frame and connects to an electrical harness. The power entry includes a 6' cable that can be field cut to the appropriate length.
Part # E1324

Ceiling Power Entry Internal

Connects to a ceilings electrical supply to the base of a frame, either directly or through any connector. It distributes up to 4-20 amp circuits and holds up to 90° 4-pair UTP category 5 cables. The power entry has a 10'-high pole, ceiling and base trim, connecting hardware, conduit and a factory-installed electrical harness. Part # E1331

Power/Cable Entry Cover

This cover conceals power or low-voltage conduits routed from the floor to the cable management tile. It can also be used without the cable management tile. The cover includes 2 floor attachment brackets and 2 trim pieces for closing gaps between the cover and the cable management tile.
Part # E1326

Baseline Harness 4 Circuit

This harness converts a non powered to a frame to a powered frame. It distributes up to a 4-20 amp circuits and provides 2 receptacle locations on each side of the frame.
Part # E1354

Pass Through Harness Frame

This harness extends power from the Ethospace powered frame through a nonpowered or wall section to an adjacent powered frame or wall section.
Part # E1342
Available Lengths: 18",24",30",36",42",48",60"

Pass Through Harness Connector

This harness coverts a nonpowered connector to a powered connector at the base line or beltine and passes power through the connector to an adjacent powered frame. The harness is UL Listed and CSA certified.
Part # E1356

Tile Height Harness

This harness is used with 1 or 2 cable access or cable channel tiles. It distributes up to 4-20 amp circuits, provides 2 receptacle access locations on each side of a frame, and includes a support bar for attaching the harness to a frame.
Part # E1357
Available widths: 24',30",36",42",48"

Power Jumper 4 Circuit

This power jumper connects power from an Ethospace baseline harness to an electrical harness. The connections for both harnesses are at the same connection point as receptacles. The power jumper cannot be used with a glazed window tile, or stacking frame.
Part # E1341

Electrical Bridge 4 Circuit to 4 Circuit

This bridge connects a D-series 4-circuit power harness to an E-series 4-circuit powered frame or connector.
Part #E1370

Vertical Wire Harness Single

This harness is used with a beltline face tile. It carries power from the baseline harness up to the beltline level in consecutive frames. Multiple vertical wire harnesses can connect and carry power from frame to frame.
Part #E1343

Baseline Box Assembly, H-Style Frame

Retrofits H-style electrical. It has a junction box that holds a hard-wired, flexible-conduit electrical system in the baseline of 1 or both sides of the frame. Double-wide, two-sided junction box, 2 blank covers , 2 port covers, cable management side cover w/o cutouts a cable management side cover with receptacles cutouts.
Part # EW400

Harness End Cap

This cap covers the unused end port or side port of an Action Office Series 2, Prospects, Q, or Ethospace electrical harness. It also serves as a visual indicator for the last harness in a series of powered products. Cap is red
Part # G1358

Receptacle 4-circuit 15 Amp

This receptacle locks into the baseline or beltline harness of an Ethospace frame,. A simplex receptacle package contains 1 receptacle; a duplex receptacle package contains 6
Part # E1311

Receptacle 4 Circuit 20 Amp

This receptacle locks into a 4 circuit electrical harness to proved power to equipment with a 20-amp standard plug head or cap. It also accepts 15-amp standard plug heads or caps. The receptacle is UL Listed.
Part #X1311

Acoustical Tile

High sound-reducing tile attaches to 1 side of a frame or to wall strips and has a fabric surface. Available w/ 2 different acoustical ratings: one ahs a Noise Reduction Coefficient (NRC) Rating of.75 and a Sound Transmission Class (STC) rating of 21: the other one has an NRC rating of.80 and STC rating of 23
Part # E1423

Tackable Tile

This 16" high tackable tile attaches to 1 side of a frame or to a wall strip to display notes and art .It has a fabric surface.
Part # E1422
Available widths: 24',30",36",42",48"

Replacement Cover

This cover upholsters a painted face tile or replaces the cover on a fabric-covered face tile, acoustical tile, or tackable tile. It has attachment strips to allow replacement of the fabric. Pkg contains 6 covers of the same fabric color.
Part # E1490 = face tile
Part # E1491= acoustical/tackable tile

Cable Access Tile

8 " high tile attaches to 1 side of a frame of equal width and has a painted, grooved, vinyl, fabric or wrapcoat surface. It cannot be used with wall strips or tile adapters.
Part # E1432 = 2 receptacles locations
Part # E1436 = 2 receptacle locations, 2 communication port locations

Glazed Window Tile

This glazed window tile attaches to 1 side of a frame of equal width, It cannot be used with wall strips, tile adapters, or a 4-ciruit power jumper.
Part # E1411
Available widths: 24',30",36",42",48"

Open Tile Squared Tile

This metal open tile finishes a frame and provides an opening for communicating, sharing equipment, or improving air circulation.Tile finishes both sides of a frame. It cannot be used with a stacking frame or with a 4-circuit power jumper.
Part # E1444
Available widths: 24',30",36",42",48"

Perforated Tile Squares

This perforated metal tile attaches to 1 side of a frame. It has 1/4" square perforation spaced 3/4" apart.
Part # E1441

Counter Top Support

This product supports a square-edge counter top. It cannot attach to veneer connectors or crown or veneer top caps. Attachment hardware is included.
Part # E2827
Available widths: 24',30",36",42",48"

Counter Top Support End Cap

This end cap closes and finishes the end of a counter top support . It has an electrical junction box to end the wiring when an adjacent counter top support with lights is used. The end cap cannot attach to a veneer connector or crown or veneer top cap.
Pkg contains 2 Part # E2829

Categories

Metro Wire Shelving

By Manufacturer

Herman Miller® Ethospace® Parts